Treshold parameter actor 2 byte / lux
Geplaatst: ma 16 mei 2016, 22:41
Hallo forumleden,
Even een vraagje of ik het bij het juiste eind heb met de programmatie.
In de ABB actor heb ik volgende functie "ondekt".. namelijk "treshold".
Bedoeling is dat ik deze setting gebruik om de 2byte waarde van het weerstation ( Lux waarde ) de output te laten schakelen.
Echter lukt het nog niet zo vlotjes.... of ben ik misschien verkeerd.
Onderstaande heb ik uit de abb manual
SA/S | 2CDC 505 056 D0207 91
3.2.3.1.6 Parameter window
A: Threshold value
In this parameter window, all settings for the function Threshold are
undertaken.
This parameter is visible if in parameter window A: Function, page 64, the
parameter function Threshold has been enabled.
The function Threshold enables the evaluation of the 1 byte or 2 byte
communication object Threshold input. As soon as the value of the
communication object falls below or exceeds a threshold value, a switching
operation can be triggered. Two independent threshold values are available.
Threshold 1 can be modified via the bus.
For further information see: Function Threshold, page 152.
With activated function Threshold, the Switch Actuator continues to receive
switch telegrams. In this way, the contact position determined by the function
Threshold can be changed, see Function chart, page 139. The function
Threshold generates a switch telegram as soon as a new threshold telegram
is received, and at the same time a new switch condition is present that
overshoots or undershoots the switch criteria.
Data type of object "Threshold input"
Options: 1 byte [0...255]
2 byte [0...65,635]
The data type for the threshold input that is received via the communication
object Threshold input can be determined here.
It is possible to choose between a 1 byte integer value and a 2 byte counter
value.
Momenteel heb ik dus het "Treshold" object in het groupsadres van mijn weerstation geplaatst
Echter had ik nog geen succes met het aan/uit schakelen van de output. Via het standaard "Switch" object werkt alles wel normaal.
Enkel reageert de output dus niet op de treshold 2byte signalen.
doe ik iets verkeerd ? Of moet je naast het bepalen van de treshold ook nog een 1bit in het schakel object sturen? => wat volgens mij niet de bedoeling kan zijn.
Even een vraagje of ik het bij het juiste eind heb met de programmatie.
In de ABB actor heb ik volgende functie "ondekt".. namelijk "treshold".
Bedoeling is dat ik deze setting gebruik om de 2byte waarde van het weerstation ( Lux waarde ) de output te laten schakelen.
Echter lukt het nog niet zo vlotjes.... of ben ik misschien verkeerd.
Onderstaande heb ik uit de abb manual
SA/S | 2CDC 505 056 D0207 91
3.2.3.1.6 Parameter window
A: Threshold value
In this parameter window, all settings for the function Threshold are
undertaken.
This parameter is visible if in parameter window A: Function, page 64, the
parameter function Threshold has been enabled.
The function Threshold enables the evaluation of the 1 byte or 2 byte
communication object Threshold input. As soon as the value of the
communication object falls below or exceeds a threshold value, a switching
operation can be triggered. Two independent threshold values are available.
Threshold 1 can be modified via the bus.
For further information see: Function Threshold, page 152.
With activated function Threshold, the Switch Actuator continues to receive
switch telegrams. In this way, the contact position determined by the function
Threshold can be changed, see Function chart, page 139. The function
Threshold generates a switch telegram as soon as a new threshold telegram
is received, and at the same time a new switch condition is present that
overshoots or undershoots the switch criteria.
Data type of object "Threshold input"
Options: 1 byte [0...255]
2 byte [0...65,635]
The data type for the threshold input that is received via the communication
object Threshold input can be determined here.
It is possible to choose between a 1 byte integer value and a 2 byte counter
value.
Momenteel heb ik dus het "Treshold" object in het groupsadres van mijn weerstation geplaatst
Echter had ik nog geen succes met het aan/uit schakelen van de output. Via het standaard "Switch" object werkt alles wel normaal.
Enkel reageert de output dus niet op de treshold 2byte signalen.
doe ik iets verkeerd ? Of moet je naast het bepalen van de treshold ook nog een 1bit in het schakel object sturen? => wat volgens mij niet de bedoeling kan zijn.